Skip to content
Home » Blogs » How to Add Weight to the Arrow Tip?: 3 Methods!

How to Add Weight to the Arrow Tip?: 3 Methods!

You might want to change the weight of your arrow for better performance. Adding weight affects the behavior of your arrow. All of this depends on what you want and what kind of archer you are. 

If you are a bowhunter, adding weight is a major factor. Increasing the weight helps in increasing momentum and better penetration. 

So, you must know How to add weight to the arrow tip? 

Weights can be added easily without any professional help. You can follow any of the three methods. They are weight tubes, inserts, and switching the point weight. All the three methods begin with detaching the node and then adding the weight. The weights are added according to choice and variation. 

Only knowing this much information won’t be of any help right? So, we have got a full detailed article covered. All the methods are described which will help you to add weight to your arrow. 

Let’s jump right in-

Adding Weight to Your Arrow: [3 Simple Methods]

There are various ways to add the proper weight. It depends on your particular archery need. However, we have to keep in mind that adding weight will affect the dynamic spine.

Adding weight to the top will weaken the dynamic spine. Because the weight will change the amount of force. The selected spine should be properly placed so that the aim remains correct.

In order to add weight, we need to first know the arrow weights. Arrows come in three weight types. They are light, medium, and heavy. You can easily calculate arrow weight and define the type. 

Once you know the weight of your arrow, you get an idea of how much weight to add. However, sometimes you might need to decrease the weight too. 

Now let’s dig deep into the methods of adding weight to your arrow tip: 

Method 1: Weight Tubes 

Weight tubes are very effective in adding weight to your arrow. It is a very simple process. Weight tubes do not affect the dynamic spine that much/ however, it provides greater momentum. 

Weight tubes are found in three, five, or eight grains per inch(GPI). So, you will have to first decide which to use. 

Once you select the ideal weight, the main process begins. First, detach the nock and slide it down the tube. Then mark at the end of the tube to cut that place. The end of the tube is where the tube flush along the shaft.

Then place the shoulder of the nock evenly with the end of the tube. This is particularly the gap where the nock slides into the shaft. 

Finally, cut the tube there, slide the tube back and attach the nock. And you have added weight to the arrow.

Method 2: Inserts 

It is one of the most common methods to add weight to an arrow. The standard inserts usually come with an arrow. They are made of aluminum and weigh around 10-15 grains.

These aluminum inserts are joined at the back of the insert. As a result, this allows the use of a modular weight system. This also indicated the high flexibility for tuning the weight.

To add weight, brass, Stainless steel or aluminum inserts are used. And their weight can vary from 50-100 grains. Also, often you might need to choose a particular bow. 

Suppose for a 50 grain arrow what bow you should choose. So, you must first decide how much weight you want to add.

Gold Tip FACT screw-in weight system or Black eagle inserts are some ideal ones. Screw-in weights are usually used separately. They can also be stacked on one another until the ideal weight is achieved. 

It is recommended to use a Tip jam so that the vibration doesn’t loosen the weight. You can easily change or add weight using a wrench. First, detach the nock and hold the wrench down the shaft to add weights.

One of the great advantages of this system is if you can use the same screw-in point or broadhead weight. You can easily adjust and tune the weight combinations anytime.

Method 3: Switching the Point Weight 

Switching the point weight is the easiest method. There are different types of screw-in and glue-on points. For the perfect placement, you can go with brass washers. They weigh 5 grains which allows the finest tuning.

Make sure to screw the points to the shaft. Screwing helps to hold them in place. 

Apart from this, you can also go for DIY arrow weights. Usually, a 1” piece will weigh around 25 grains.  

So first cut the thread then screw the back head. And after that add all the thread to the lower part of the insert. Make sure the field point is fit and then apply glue around the threads. 

This DIY method might not work for everyone. So it’s better to stick to the proper methods for the best result. 

Now, it might be confusing to choose the weights/inserts. So, we have recommended some good ones here-

These are some weight screws and inserts you can use for adding weight. They are highly recommended and suitable for any arrows. 


Why  is an arrow weighted? 

Finding the right weight will result in better performance. So, it is necessary to weigh your arrow in the perfect balance. The perfect rule of thumb for arrow weight is 8-10 grains for every lbs of pull. 

How does adding weight affect the spine? 

Adding weight to the tip of your arrow will weaken the spine. It also changes the amount of force. A 25 grains of weight added to the tip will weaken the spine by 2 ½ pounds.

Do I have to glue the inserts? 

No, you don’t need to glue the inserts. Because gluing the surface of the insert may lead to extra adhesion. Though you can use TIP GRIP adhesive. It is recommended not to use hot glue. 


So, to conclude now you know how to add weight to the arrow tip? For extensive momentum and better penetration, adding weight to the tip is an ideal decision. 

However, make sure you are adding the proper weight. Often, being overweight can lead to heavier arrows. This will not only create a problem for the arrow but also won’t reach your aim correctly. 

That’s all for today! Hope we could answer your question and help you. All the best for your perfect aim. Stay safe!

Leave a Reply

Your email address will not be published. Required fields are marked *