Skip to content
Home » Blogs » How to Reduce Draw Weight on A Recurve Bow?- [3 Methods]

How to Reduce Draw Weight on A Recurve Bow?- [3 Methods]

It’s very frustrating when you find your bow is much-drawn. On top of that, it’s quite hard to control your bow. 

So, how to reduce draw weight on a recurve bow? 

Well, it is quite possible to reduce the draw weight on your recurve bow. You can change the limbs to lower-weight limbs to reduce the draw weight. Otherwise, you can adjust the limb bolts. Or tinning the fiberglass can also reduce the draw weight of your recurve bow. 

You might be still in the blue about the matter. Let’s jump to the detailed discussion. 

How to Reduce Draw Weight On A Recurve Bow? 

The ability to adjust the draw weight of a compound bow is well known. The weight is mainly 60-70 pound compound bows. The majority of them have a 10-pound standards-setting. However, some can be adapted from 5-70 pounds.

Did you know that the mass of some recurve bows can be adjusted? Specific recurve bows allow you to change the drawing load. Recurve bows are the only ones that will work with this.

But why should you adjust or draw weight from your recurve bow? Let’s find out!

Why Drow Weight Is Needed? 

At a higher draw weight, you may have difficulty keeping the bow still. As a result, you reduce it to exert more control. The draw weight can assist you in gaining control of your recurve bow.

Other archers may find that increasing the shoot weight gives them more control. Another reason to change the draw weight of an arrow is to get it to tune better.

If the tune is similar to the draw weight that was set. A small change in weight may be all that is required to achieve a perfect flight. Mainly the appropriate weight is 50 pounds for a recurve bow. 

Also, you need to select the perfect arrow for a 50-pound bow for batter flight. Here are some techniques for lowering your bow’s draw weight.

Method 01: Add Limbs With Lower Drew Weight 

You can solve your problem by adding limbs with a lower draw weight. You can change the limbs to change the draw weight.

If it’s a three-piece revocation bow. It is made up of two limbs and a riser. Then you can experiment with changing the limbs.

But here’s something you’ll require for both limbs. Furthermore, both limbs must be the same weight. It will improve the bow’s stability. Changing both limbs may result in 5-10 pound weights being drawn from the bow.

Here are some low-weighted limbs for you to try on. 

These limbs are topnotch in quality. And they will be good archery partners. 

However, if one’s bow is a two-piece takedown, this trick will not work. A two-piece take-down bow’s weight cannot be changed. Then you may need to change your bow or try a different method.

Method 02: Adjusting The Limb Bolt 

Another method of drawing mass on a recurve bow is to adjust the limb’s bolt. Dovetail pockets on an ILF or Hoyt Formula riser will capture the dovetail casings on the limbs. They will also have limb bolts.

These risers have adjustable limb bolts. Turning the limb bolts clockwise brings them closer to a riser and increases the draw weight. Anticlockwise adjustment tends to raise the bolts and reduces draw weight.

In addition, nearly all risers have adjustable limb bolts. After making adjustments, use a locking bolt to keep the limb bolt in place.

It is critical to unlock these screws before adjusting the limb bolts. When the adjustments are finished, lock them again.

ILF recurve bow bolts have a suggested best working range. For the lowest draw weight, start at a maximum altitude of 20mm (13/16 of an inch). As well as trying to adjust to a height limit of 15mm (5/8 inch).

For the most powerful draw weight. These measurements are taken from the undersurface of the limb bolt. From the limb pouch beneath its surface.

It is critical to remember that equal turns must be put into and picked out of the top and bottom limbs. It will keep the tiller in place. The measurements of a bow’s tiller will be affected by unequal turns.

This can have an impact on the bow’s tune as well as how it gets to sit in your hand. It can also interfere with the flight of the arrow.

Method 03: Thinning The Fibreglass

Another method for reducing draw weight on a recurve bow is to tin the fiberglass. Grind the glass first, then the sides if trapping or reshaping of the limb is required.

The glass does the majority of the work, as stated above. Furthermore, thinning the glass means allowing you to lose weight more effectively. Granted, your Robertson Stykbow (or another bow) will not have the same limb dynamics.

It looked the same before you cut through the finish and attacked the glass. But, in any case, it became smoother and had less draw weight. In the end, it was a win for me. Because the re-tuned bows could be hooted a lot louder.

However, think of the glass as a body to maintain the lams intact, rather than hallowed ground. 

FAQs 

What should my recurve bow’s draw weight be?

Choose a recurve bow with a minimum draw weight of 40 pounds. You can hunt smaller games like turkey and rabbit with a 35 or even 30-pound bow. But anything larger (deer, elk) requires a bow weighing 40 pounds or more. So, while you might not be able to handle more than 30 lbs.

Is a 70 lb draw too much?

Some shooters can hit targets weighing 70, 80, or 90 pounds, but the majority of adult males shoot between 60 and 70 pounds. Today’s bows are extremely efficient. And 40lb compound bows are more than capable of taking down many large game animals. Anything over 40 lbs is acceptable for whitetail deer hunting.  

Are recurve bows appropriate for beginners?

The Samick Sage Recurve Bow is widely regarded as an excellent beginner bow. And you visit other websites similar to ours (but why would you?). They may also recommend this bow for beginners. There are a few reasons why the Samick is a good choice for a new archer. It’s got takedown limbs.

Bottom Line 

Thank you for reading the whole article to the end. Hope now you are clear about how to reduce draw weight on a recurve bow

Adjusting the bow within your reach is the top priority of every archer. If you are unable to adjust your bow you should buy a new one instead. 

Best of luck. 

Leave a Reply

Your email address will not be published. Required fields are marked *